Overview

Recalls are issued for defects or faults which have the potential to cause injury. Manufacturers or importers seek to inform the original buyer if their vehicle is subject to a recall and of the steps required to remedy the defect or fault. However, manufacturers or importers may not have the contact details of subsequent owners. Please note that the recalls below are for Australian-delivered vehicles only. Furthermore, the number of recalls should not be taken as an indication of a model’s reliability or its safety more generally.

Recalls: Toyota XU70 Kluger

2021 Toyota XU70 Kluger: seat frames do not meet Australian Design Rules

In June 2022, recall campaign XGG05 was issued for 2021 Toyota XU70 Kluger vehicles. Due to a manufacturing issue, the front seat-back frames were not manufactured with the minimum radius criteria to meet the requirements of Australian Design Rule (ADR 3/03). For the VINs of the recalled vehicles, please see REC-005459.

2023 Toyota XU70 Kluger and Kluger Hybrid: driver’s airbag may not deploy

In October 2023, recall campaign YGG39 was issued for 2023 Toyota Kluger vehicles with 2.4-litre petrol engines and Kluger Hybrid vehicles with 2.5-litre petrol engines. In these vehicles, the driver side airbag wiring harness connection may become loose over time. If this occurred, the airbag warning light would illuminate and the driver’s side airbag would not deploy. In the event of a collision, the failure of the airbag to deploy could increase the driver’s risk of injury. For the VINs of the recalled vehicles, please see REC-005797.

2021-23 Toyota XU70 Kluger and Kluger Hybrid: front bumper cover assembly may detach

In November 2023, recall campaign YGG74 was issued for 2021-23 Toyota XU70 Kluger and Kluger Hybrid vehicles. These vehicles were fitted with a resin front lower bumper cover assembly that was connected with mounting tabs. If there was a minor impact to the lower front bumper cover that caused the mounting tabs to detach from the vehicle, one or more parts of this assembly could detach. These parts could become a hazard hazard that increased the risk of a collision and injury for other road users. As part of the recall, the mounting tabs were to be inspected for damage. If there was no damage, the Toyota dealer would fit ‘retention hardware’ with an improved design. If there was damage to the front bumper cover assembly, the Toyota dealer would replace the upper and lower front bumper cover. For the VINs of the recalled vehicles, please see REC-005813.

Problems and faults: Toyota XU70 Kluger

Overview

This section identifies potential problems, causes and fixes based on the experiences of owners and repairers, online sources and technical service bulletins. This information is provided solely for reference purposes and AustralianCar.Reviews recommends that only properly qualified persons carry out repairs or modifications. Furthermore, the number of items below should not be taken as an indicator of a model’s reliability or the frequency with which they may occur.

To report a problem or fault to the AustralianCar.Reviews team, please use the Contact Us form. Note that AustralianCar.Reviews does not offer advice on automotive problems or disputes; such enquiries will not receive a reply. For vehicles purchased from dealers after 1 January 2011, please see our Australian Consumer Law fact sheet.

Problems and faults: Toyota XU70 Kluger

No troubleshooting information is currently available for the Toyota XU70 Kluger.

Overview

Recalls are issued for defects or faults which have the potential to cause injury. Manufacturers or importers seek to inform the original buyer if their vehicle is subject to a recall and of the steps required to remedy the defect or fault. However, manufacturers or importers may not have the contact details of subsequent owners. Please note that the recalls below are for Australian-delivered vehicles only. Furthermore, the number of recalls should not be taken as an indication of a model’s reliability or its safety more generally.

Recalls: Genesis JW1 GV60

2022-23 Genesis JW1 GV60: rear driveshaft could break

In June 2023, recall campaign 31D040 was issued for 2022-23 Genesis JW1 GV60 vehicles. Due to a manufacturing defect, the vehicle’s rear driveshaft may fracture and this would result in a sudden loss of motive power. If this occurred whilst driving, there would be an increased risk of a collision and injury for both vehicle occupants and other road users. Until the recall works were carried out, drivers were advised to drive with caution and listen for any abnormal noise. If noise could be heard from the rear of the vehicle, owners were advised to have to have vehicle delivered to a Genesis dealer. For the VINs of the recalled vehicles, please see REC-005698.

2022-24 Genesis JW1 GV60: seatbelt pre-tensioner inflator cap and metal fragments

In June 2023, recall campaign 31D015 was issued for 2022-24 Genesis JW1 GV60 vehicles. Due to a manufacturing issue, the seatbelt pre-tensioner inflator cap may fracture when deployed in the event of a collision. If the seatbelt pre-tensioner inflator cap fractured, metal fragments may be propelled at high speed towards the vehicle occupants – these could cause serious injury. For the VINs of the recalled vehicles, please see REC-005715.

2022-24 Genesis JW1 GV60: ICCU software, battery drainage and potential loss of power

In April 2024, recall campaign 41D034 was issued for 2022-24 Genesis JW1 GV60 vehicles. Due to a software issue in the Integrated Charging Control Unit (ICCU), the auxiliary 12 volt battery may not charge as intended – this could cause battery drainage and a loss of motive power. If a loss of motive power occurred whilst driving, there would be an increased risk of a collision and injury for both vehicle occupants and other road users. For this recall, a Genesis Motor Australia dealership was to update the ICCU software. For the VINs of the recalled vehicles, please see REC-005943.

Problems and faults: Genesis JW1 GV60

Overview

This section identifies potential problems, causes and fixes based on the experiences of owners and repairers, online sources and technical service bulletins. This information is provided solely for reference purposes and AustralianCar.Reviews recommends that only properly qualified persons carry out repairs or modifications. Furthermore, the number of items below should not be taken as an indicator of a model’s reliability or the frequency with which they may occur.

To report a problem or fault to the AustralianCar.Reviews team, please use the Contact Us form. Note that AustralianCar.Reviews does not offer advice on automotive problems or disputes; such enquiries will not receive a reply. For vehicles purchased from dealers after 1 January 2011, please see our Australian Consumer Law fact sheet.

Problems and faults: Genesis JW1 GV60

No troubleshooting information is currently available for the Genesis JW1 GV60.

Overview

Recalls are issued for defects or faults which have the potential to cause injury. Manufacturers or importers seek to inform the original buyer if their vehicle is subject to a recall and of the steps required to remedy the defect or fault. However, manufacturers or importers may not have the contact details of subsequent owners. Please note that the recalls below are for Australian-delivered vehicles only. Furthermore, the number of recalls should not be taken as an indication of a model’s reliability or its safety more generally.

Recalls: Genesis JX1 GV80

2021 Genesis JX1 GV80 2.5T GDI: defective fuel delivery pipe could leak fuel

In June 2021, recall campaign 11D051 was issued for 2021 Genesis JX1 GV80 2.5T GDI vehicles. The fuel delivery pipes for these vehicles may be defective and fuel may therefore leak out of the pipes. Fuel leakage created a fire risk when the engine was hot and a vehicle fire increased the risk of a collision; both circumstances increased the risk of injury to vehicle occupants, other road and bystanders, and/or damage to property. For the VINs of the recalled vehicles, please see REC-001660.

2020-24 Genesis JX1 GV80: seatbelt pre-tensioner inflator cap and metal fragments

In June 2023, recall campaign 31D015 was issued for 2020-24 Genesis JX1 GV80 vehicles. Due to a manufacturing issue, the seatbelt pre-tensioner inflator cap may fracture when deployed in the event of a collision. If the seatbelt pre-tensioner inflator cap fractured, metal fragments may be propelled at high speed towards the vehicle occupants – these could cause serious injury. For the VINs of the recalled vehicles, please see REC-005715.

2021-22 Genesis JX1 GV80: fuel pump impeller could deform and interrupt fuel supply

In August 2024, recall campaign 41D073 was issued for 2021-22 Genesis JX1 GV80 vehicles. Due to a manufacturing defect, the fuel pump impeller may deform under certain conditions, interrupting the fuel supply. If this occurred, the engine could stall and the vehicle would experience a sudden loss of motive power. If this occurred whilst driving, the risk of a collision and injury to both vehicle occupants and other road users would be increased. For this recall, a Genesis Motor Australia dealer was to inspect and replace the fuel pump impeller. For the VINs of the recalled vehicles, please see REC-006055.

Problems and faults: Genesis JX1 GV80

Overview

This section identifies potential problems, causes and fixes based on the experiences of owners and repairers, online sources and technical service bulletins. This information is provided solely for reference purposes and AustralianCar.Reviews recommends that only properly qualified persons carry out repairs or modifications. Furthermore, the number of items below should not be taken as an indicator of a model’s reliability or the frequency with which they may occur.

To report a problem or fault to the AustralianCar.Reviews team, please use the Contact Us form. Note that AustralianCar.Reviews does not offer advice on automotive problems or disputes; such enquiries will not receive a reply. For vehicles purchased from dealers after 1 January 2011, please see our Australian Consumer Law fact sheet.

Problems and faults: Genesis JX1 GV80

No troubleshooting information is currently available for the Genesis JX1 GV80.

Overview

Recalls are issued for defects or faults which have the potential to cause injury. Manufacturers or importers seek to inform the original buyer if their vehicle is subject to a recall and of the steps required to remedy the defect or fault. However, manufacturers or importers may not have the contact details of subsequent owners. Please note that the recalls below are for Australian-delivered vehicles only. Furthermore, the number of recalls should not be taken as an indication of a model’s reliability or its safety more generally.

Recalls: Genesis JK1 GV70

2021-24 Genesis JK1 GV70: seatbelt pre-tensioner inflator cap and metal fragments

In June 2023, recall campaign 31D015 was issued for 2021-24 Genesis JK1 GV70 vehicles. Due to a manufacturing issue, the seatbelt pre-tensioner inflator cap may fracture when deployed in the event of a collision. If the seatbelt pre-tensioner inflator cap fractured, metal fragments may be propelled at high speed towards the vehicle occupants – these could cause serious injury. For the VINs of the recalled vehicles, please see REC-005715.

2022-24 Genesis JK1 GV70: ICCU software, battery drainage and potential loss of power

In April 2024, recall campaign 41D034 was issued for 2022-24 Genesis JK1 GV70 vehicles. Due to a software issue in the Integrated Charging Control Unit (ICCU), the auxiliary 12 volt battery may not charge as intended – this could cause battery drainage and a loss of motive power. If a loss of motive power occurred whilst driving, there would be an increased risk of a collision and injury for both vehicle occupants and other road users. For this recall, a Genesis Motor Australia dealership was to update the ICCU software. For the VINs of the recalled vehicles, please see REC-005943.

2021-22 Genesis JK1 GV70: fuel pump impeller could deform and interrupt fuel supply

In August 2024, recall campaign 41D073 was issued for 2021-22 Genesis JK1 GV70 vehicles. Due to a manufacturing defect, the fuel pump impeller may deform under certain conditions, interrupting the fuel supply. If this occurred, the engine could stall and the vehicle would experience a sudden loss of motive power. If this occurred whilst driving, the risk of a collision and injury to both vehicle occupants and other road users would be increased. For this recall, a Genesis Motor Australia dealer was to inspect and replace the fuel pump impeller. For the VINs of the recalled vehicles, please see REC-006055.

Problems and faults: Genesis JK1 GV70

Overview

This section identifies potential problems, causes and fixes based on the experiences of owners and repairers, online sources and technical service bulletins. This information is provided solely for reference purposes and AustralianCar.Reviews recommends that only properly qualified persons carry out repairs or modifications. Furthermore, the number of items below should not be taken as an indicator of a model’s reliability or the frequency with which they may occur.

To report a problem or fault to the AustralianCar.Reviews team, please use the Contact Us form. Note that AustralianCar.Reviews does not offer advice on automotive problems or disputes; such enquiries will not receive a reply. For vehicles purchased from dealers after 1 January 2011, please see our Australian Consumer Law fact sheet.

Problems and faults: Genesis JK1 GV70

No troubleshooting information is currently available for the Genesis JK1 GV70.

Overview

Recalls are issued for defects or faults which have the potential to cause injury. Manufacturers or importers seek to inform the original buyer if their vehicle is subject to a recall and of the steps required to remedy the defect or fault. However, manufacturers or importers may not have the contact details of subsequent owners. Please note that the recalls below are for Australian-delivered vehicles only. Furthermore, the number of recalls should not be taken as an indication of a model’s reliability or its safety more generally.

Recalls: Genesis RG3 G80

2021 Genesis RG3 G80 2.5T GDI: defective fuel delivery pipe could leak fuel

In June 2021, recall campaign 11D051 was issued for 2021 Genesis RG3 G80 2.5T GDI vehicles. The fuel delivery pipes for these vehicles may be defective and fuel may therefore leak out of the pipes. Fuel leakage created a fire risk when the engine was hot and a vehicle fire increased the risk of a collision; both circumstances increased the risk of injury to vehicle occupants, other road and bystanders, and/or damage to property. For the VINs of the recalled vehicles, please see REC-001660.

2022 Genesis RG3 G80 EV: seatbelt pre-tensioner inflator cap and metal fragments

In December 2022, recall campaign 21D148 was issued for 2022 Genesis RG3 G80 EV vehicles. Due to a manufacturing issue, the seatbelt pre-tensioner inflator cap may fracture when deployed in the event of a collision. If the seatbelt pre-tensioner inflator cap fractured, metal fragments may be propelled at high speed towards the vehicle occupants – these could cause serious injury. For the VINs of the recalled vehicles, please see REC-005574.

2020-24 Genesis RG3 G80: seatbelt pre-tensioner inflator cap and metal fragments

In June 2023, recall campaign 31D015 was issued for 2020-24 Genesis RG3 G80 vehicles. Due to a manufacturing issue, the seatbelt pre-tensioner inflator cap may fracture when deployed in the event of a collision. If the seatbelt pre-tensioner inflator cap fractured, metal fragments may be propelled at high speed towards the vehicle occupants – these could cause serious injury. For the VINs of the recalled vehicles, please see REC-005715.

2022-24 Genesis RG3 G80: ICCU software, battery drainage and potential loss of power

In April 2024, recall campaign 41D034 was issued for 2022-24 Genesis RG3 G80 vehicles. Due to a software issue in the Integrated Charging Control Unit (ICCU), the auxiliary 12 volt battery may not charge as intended – this could cause battery drainage and a loss of motive power. If a loss of motive power occurred whilst driving, there would be an increased risk of a collision and injury for both vehicle occupants and other road users. For this recall, a Genesis Motor Australia dealership was to update the ICCU software. For the VINs of the recalled vehicles, please see REC-005943.

2021-22 Genesis RG3 G80: fuel pump impeller could deform and interrupt fuel supply

In August 2024, recall campaign 41D073 was issued for 2021-22 Genesis RG3 G80 vehicles. Due to a manufacturing defect, the fuel pump impeller may deform under certain conditions, interrupting the fuel supply. If this occurred, the engine could stall and the vehicle would experience a sudden loss of motive power. If this occurred whilst driving, the risk of a collision and injury to both vehicle occupants and other road users would be increased. For this recall, a Genesis Motor Australia dealer was to inspect and replace the fuel pump impeller. For the VINs of the recalled vehicles, please see REC-006055.

Problems and faults: Genesis RG3 G80

Overview

This section identifies potential problems, causes and fixes based on the experiences of owners and repairers, online sources and technical service bulletins. This information is provided solely for reference purposes and AustralianCar.Reviews recommends that only properly qualified persons carry out repairs or modifications. Furthermore, the number of items below should not be taken as an indicator of a model’s reliability or the frequency with which they may occur.

To report a problem or fault to the AustralianCar.Reviews team, please use the Contact Us form. Note that AustralianCar.Reviews does not offer advice on automotive problems or disputes; such enquiries will not receive a reply. For vehicles purchased from dealers after 1 January 2011, please see our Australian Consumer Law fact sheet.

Problems and faults: Genesis RG3 G80

No troubleshooting information is currently available for the Genesis RG3 G80.

Overview

Recalls are issued for defects or faults which have the potential to cause injury. Manufacturers or importers seek to inform the original buyer if their vehicle is subject to a recall and of the steps required to remedy the defect or fault. However, manufacturers or importers may not have the contact details of subsequent owners. Please note that the recalls below are for Australian-delivered vehicles only. Furthermore, the number of recalls should not be taken as an indication of a model’s reliability or its safety more generally.

Recalls: BMW U11 iX1

2022-23 BMW U11 iX1: front left drive shaft could detach

In August 2023, recall campaign 0031100200 was issued for 2022-23 BMW U11 iX1 vehicles. Due to a manufacturing defect, the front left drive shaft may become loose and detach from the eDrive. If this occurred, the vehicle would experience a sudden loss of motive power and the driver would be alerted by warning signals in the instrument cluster. A sudden loss of motive power whilst driving increased the risk of a collision and injury for both vehicle occupants and other road users. For the VINs of the recalled vehicles, please see REC-005745.

2022-23 BMW U11 iX1: front right drive shaft could detach

In August 2023, recall campaign 0031110200 was issued for 2022-23 BMW U11 iX1 vehicles. Due to a manufacturing defect, the front right drive shaft may become loose and detach from the eDrive. If this occurred, the vehicle would experience a sudden loss of motive power and the driver would be alerted by warning signals in the instrument cluster. A sudden loss of motive power whilst driving increased the risk of a collision and injury for both vehicle occupants and other road users. For the VINs of the recalled vehicles, please see REC-005746.

2022-23 BMW U11 iX1: reduced braking assistance; loss of ABS and DSC

Due to a manufacturing defect, signal interference may occur within the electronics of the brake system. If this occurred, the driver may need to apply greater force to the brake pedal for braking, and braking distances would likely increase. Furthermore, the anti-lock braking system (ABS) and dynamic stability control system (DSC) would not be available. Drivers would be alerted of this condition by the brake warning light in the instrument cluster, and a message in the central display. While the vehicle would remain controllable, the risk of a collision and injury to both vehicle occupants and other road users was increased. For this recall, a BMW dealer was to replace the electronic brake system controller. For the VINs of the recalled vehicles, please see REC-005906.

Problems and faults: BMW U11 iX1

Overview

This section identifies potential problems, causes and fixes based on the experiences of owners and repairers, online sources and technical service bulletins. This information is provided solely for reference purposes and AustralianCar.Reviews recommends that only properly qualified persons carry out repairs or modifications. Furthermore, the number of items below should not be taken as an indicator of a model’s reliability or the frequency with which they may occur.

To report a problem or fault to the AustralianCar.Reviews team, please use the Contact Us form. Note that AustralianCar.Reviews does not offer advice on automotive problems or disputes; such enquiries will not receive a reply. For vehicles purchased from dealers after 1 January 2011, please see our Australian Consumer Law fact sheet.

Problems and faults: BMW U11 iX1

No troubleshooting information is currently available for the BMW U11 iX1.

Overview

Recalls are issued for defects or faults which have the potential to cause injury. Manufacturers or importers seek to inform the original buyer if their vehicle is subject to a recall and of the steps required to remedy the defect or fault. However, manufacturers or importers may not have the contact details of subsequent owners. Please note that the recalls below are for Australian-delivered vehicles only. Furthermore, the number of recalls should not be taken as an indication of a model’s reliability or its safety more generally.

Recalls: MG MG3

2021 MG MG3: faulty fuel fuel-tank retaining bolts

In June 2021, recall campaign MG3STRP was issued for 2021 MG MG3 vehicles. In these vehicles, the fuel-tank strap retaining bolts may be faulty and could fail. This could result in movement of the vehicle’s fuel tank, and it could detach from the vehicle. If this occurred, fuel may leak from the tank, which could result in a fire and/or accident, thereby increasing the risk of injury to vehicle occupants and other road users. To fix, an MG dealer was to replace the fuel-tank retaining bolts. For the VINs of the recalled vehicles, please see REC-001632.

Problems and faults: MG MG3

Overview

This section identifies potential problems, causes and fixes based on the experiences of owners and repairers, online sources and technical service bulletins. This information is provided solely for reference purposes and AustralianCar.Reviews recommends that only properly qualified persons carry out repairs or modifications. Furthermore, the number of items below should not be taken as an indicator of a model’s reliability or the frequency with which they may occur.

To report a problem or fault to the AustralianCar.Reviews team, please use the Contact Us form. Note that AustralianCar.Reviews does not offer advice on automotive problems or disputes; such enquiries will not receive a reply. For vehicles purchased from dealers after 1 January 2011, please see our Australian Consumer Law fact sheet.

Problems and faults: MG MG3

No troubleshooting information is currently available for the MG MG3.

Overview

Recalls are issued for defects or faults which have the potential to cause injury. Manufacturers or importers seek to inform the original buyer if their vehicle is subject to a recall and of the steps required to remedy the defect or fault. However, manufacturers or importers may not have the contact details of subsequent owners. Please note that the recalls below are for Australian-delivered vehicles only. Furthermore, the number of recalls should not be taken as an indication of a model’s reliability or its safety more generally.

Recalls: MG AS23 HS

2021-22 MG HS PHEV and MG HS +EV: carpet underlay could cause vehicle fire

In May 2023, recall campaign RMGHSEVPTC was issued for 2021-22 MG HS PHEV and MG HS +EV vehicles. Due to a manufacturing defect, a carpet underlay may be positioned between the nut and the electrical ground stud. Due to vibrations whilst driving the nut could loosen overtime and this could cause the wiring beneath the floor to overheat and cause a fire inside the vehicle. A vehicle fire posed a risk of injury to vehicle occupants, other road users and bystanders. For the VINs of the recalled vehicles, please see REC-005652.

Problems and faults: MG AS23 HS

Overview

This section identifies potential problems, causes and fixes based on the experiences of owners and repairers, online sources and technical service bulletins. This information is provided solely for reference purposes and AustralianCar.Reviews recommends that only properly qualified persons carry out repairs or modifications. Furthermore, the number of items below should not be taken as an indicator of a model’s reliability or the frequency with which they may occur.

To report a problem or fault to the AustralianCar.Reviews team, please use the Contact Us form. Note that AustralianCar.Reviews does not offer advice on automotive problems or disputes; such enquiries will not receive a reply. For vehicles purchased from dealers after 1 January 2011, please see our Australian Consumer Law fact sheet.

Problems and faults: MG AS23 HS

No troubleshooting information is currently available for the MG AS23 HS.

Overview

Recalls are issued for defects or faults which have the potential to cause injury. Manufacturers or importers seek to inform the original buyer if their vehicle is subject to a recall and of the steps required to remedy the defect or fault. However, manufacturers or importers may not have the contact details of subsequent owners. Please note that the recalls below are for Australian-delivered vehicles only. Furthermore, the number of recalls should not be taken as an indication of a model’s reliability or its safety more generally.

Recalls: Volkswagen NF Amarok

2023 Volkswagen NF Amarok: front driveshaft may break

In November 2023, recall campaign 39F7 was issued for 2023 Volkswagen NF Amarok vehicles. Due to a manufacturing defect, the front driveshaft may become damaged and break. If this occurred, the vehicle would experience a sudden loss of motive power which could increase the risk of injury to both vehicle occupants and other road users. For the VINs of the recalled vehicles, please see REC-005829.

2023 Volkswagen NF Amarok: rear driveshaft bolts could become loose and detach

In November 2023, recall campaign 39F8 was issued for 2023 Volkswagen Amarok vehicles because the rear driveshaft bolts may not have been sufficiently tightened during production. The driveshaft bolts could therefore become loose and detach. If this occurred, the vehicle may experience a sudden loss of motive power. This condition could increase the risk of a collision and injury to vehicle occupants and/or other road users. For the VINs of the recalled vehicles, please see REC-005838.

Problems and faults: Volkswagen NF Amarok

Overview

This section identifies potential problems, causes and fixes based on the experiences of owners and repairers, online sources and technical service bulletins. This information is provided solely for reference purposes and AustralianCar.Reviews recommends that only properly qualified persons carry out repairs or modifications. Furthermore, the number of items below should not be taken as an indicator of a model’s reliability or the frequency with which they may occur.

To report a problem or fault to the AustralianCar.Reviews team, please use the Contact Us form. Note that AustralianCar.Reviews does not offer advice on automotive problems or disputes; such enquiries will not receive a reply. For vehicles purchased from dealers after 1 January 2011, please see our Australian Consumer Law fact sheet.

Problems and faults: Volkswagen NF Amarok

No troubleshooting information is currently available for the Volkswagen NF Amarok.

Overview

Recalls are issued for defects or faults which have the potential to cause injury. Manufacturers or importers seek to inform the original buyer if their vehicle is subject to a recall and of the steps required to remedy the defect or fault. However, manufacturers or importers may not have the contact details of subsequent owners. Please note that the recalls below are for Australian-delivered vehicles only. Furthermore, the number of recalls should not be taken as an indication of a model’s reliability or its safety more generally.

Recalls: Ford JK Puma

2023 Ford JK Puma: incorrect Restraint Control Module configuration

In September 2023, recall campaign 23S52 was issued for 2023 Ford JK Puma vehicles. During the manufacturing process, the Restraint Control Module (RCM) was loaded with an incorrect configuration. As a result, if an incorrect replacement part was installed in the system, warnings would not be displayed and the seatbelt pretensioners and airbags may not perform as intended in the event of a collision. This condition had the potential to increase the risk and severity of injury to vehicle occupants. For this recall, a Ford dealer was to update the RCM configuration. For the VINs of the recalled vehicles, please see REC-005775.

Problems and faults: Ford JK Puma

Overview

This section identifies potential problems, causes and fixes based on the experiences of owners and repairers, online sources and technical service bulletins. This information is provided solely for reference purposes and AustralianCar.Reviews recommends that only properly qualified persons carry out repairs or modifications. Furthermore, the number of items below should not be taken as an indicator of a model’s reliability or the frequency with which they may occur.

To report a problem or fault to the AustralianCar.Reviews team, please use the Contact Us form. Note that AustralianCar.Reviews does not offer advice on automotive problems or disputes; such enquiries will not receive a reply. For vehicles purchased from dealers after 1 January 2011, please see our Australian Consumer Law fact sheet.

Problems and faults: Ford JK Puma

No troubleshooting information is currently available for the Ford JK Puma.